Blog › Finishing and gifts

How to Frame and Display Finished Cross Stitch

8 November 2026 · 5 min read · By Crosserly

To frame cross stitch, wash it gently, press it face down on a towel, stretch it over acid-free board by lacing or pinning the edges at the back, then put it in a frame with the glass kept off the stitches, or left out. For a quicker finish, display it in an embroidery hoop, or make it into a card, cushion or ornament.

Wash it first

Hands leave oils on the fabric, and hoops leave rings. A gentle wash takes out the marks, softens creases and plumps up the stitches. Do it before framing: once the piece is laced to a board it cannot go in water. If you are not sure your threads are colourfast (some hand-dyed threads can run), check the maker’s advice first.

  1. Fill a clean bowl with cool or lukewarm water and a few drops of mild soap. No bleach.
  2. Soak the stitching for 10 to 15 minutes, swishing it gently. Do not rub or scrub the stitches.
  3. Rinse in cool, clean water until no soap is left.
  4. If any colour runs, keep rinsing in cold water until the water stays clear. Do not leave it to dry while colour is still running.
  5. Roll it in a clean towel and press to soak up the water. Never wring it.

Press it face down on a towel

Pressing flattens the fabric but should not flatten the stitches. The towel is the trick: the stitches sink into its pile instead of being squashed.

  1. Fold a thick, fluffy towel in half on the ironing board.
  2. Lay the stitching on it face down, while it is still slightly damp.
  3. If you used metallic threads, cover the back with a thin cotton cloth.
  4. Press with a warm iron, lifting and pressing rather than sliding, from the middle outwards.
  5. Let it dry flat. If the rows of stitches look crooked, ease the fabric square with your fingers while it is still damp.

Mount it on board: lacing or pinning

To sit flat and tight in a frame, the fabric is stretched over a stiff board cut to fit the frame. Use acid-free mount board or foam board: ordinary cardboard contains acids that can turn fabric yellow over the years. You need about 7.5 cm (3 in) of spare fabric on every side to wrap round the board. The fabric calculator allows for this when it tells you how much fabric to cut.

Lacing is the traditional way, and nothing is glued, so it can always be undone:

  1. Lay the stitching face down and put the board on top. Check that the design is centred and the rows run straight.
  2. Fold the top and bottom edges over the back of the board.
  3. With strong thread, such as crochet cotton, lace from one edge to the other in a zigzag, with each pass about 2 cm (¾ in) apart.
  4. Tighten the lacing a little at a time, from the middle outwards, until the fabric is taut and the rows are straight.
  5. Fold the corners in neatly, then lace the two side edges the same way.

Pinning is quicker. On foam board about 5 mm (¼ in) thick, push pins through the fabric into the edge of the board every 1 to 2 cm, top and bottom first, then the sides. Self-adhesive mounting boards are quickest of all, but the glue is hard to undo, so many stitchers keep them for small everyday pieces rather than heirlooms.

Glass or no glass?

Both choices are fine: it depends on where the piece will hang.

With glassWithout glass
Dust and greaseKept offNeeds a soft brush now and then
TextureFlattened if the glass touchesYou see every stitch
ReflectionsSome, unless non-reflectiveNone
SuitsKitchens, hallways, sunny roomsQuiet rooms out of the sun

If you use glass, keep it off the stitches. A mount (a card border with a window cut in it, called a mat in the US) or thin spacers inside the frame hold the glass a few millimetres away. That stops the stitches being crushed and lets air move, so damp is not trapped against the fabric. UV-filtering glass slows fading; non-reflective glass cuts glare.

Tip: Hang stitching out of direct sunlight and away from steamy bathrooms. Sun fades thread over time, glass or no glass.

Finish it in a hoop

An embroidery hoop is the quickest frame of all, and suits small or round designs. Choose a wooden hoop a little bigger than the design, so there is an even border of fabric around it.

  1. Put the stitching in the hoop, centred and straight, and tighten the screw until the fabric is drum tight. Turn the screw to the top for hanging.
  2. Trim the spare fabric to about 3 cm (1¼ in) beyond the hoop all round.
  3. Sew a running stitch round the edge of the spare fabric and pull it tight, so it gathers behind the hoop. Tie it off. Some stitchers glue the edge to the inner ring instead.
  4. Cut a circle of felt the size of the inner ring and stitch or glue it over the back to hide the edges.
  5. Hang it from the screw with ribbon or a loop of thread.

Other ways to show it off

For first designs that look polished once finished, see beginner projects that look professional. And if the piece is a present, cross stitch gifts covers planning so the framing is not rushed.

Using a professional framer

Crosserly is a free cross stitch pattern maker. Turn a photo or a few words into a chart in real thread colours, or draw your own, then print it or follow it on your phone.

Make a pattern, free

Questions

Do you have to wash cross stitch before framing?

No, but it usually helps. A gentle wash removes hand oils and hoop marks and makes the stitches look fuller. Skip it if you are not sure your threads are colourfast.

Should cross stitch be framed with glass?

It is up to you. Glass keeps dust off but flattens the stitches if it touches them, so use a mount or spacers to keep a gap. Many stitchers leave the glass out so the texture shows.

What size frame do I need for my cross stitch?

Measure the stitched design, then add the border you want on each side. A design 25 × 18 cm (10 × 7 in) with a 5 cm (2 in) border all round needs a frame opening of about 35 × 28 cm (14 × 11 in).

Read next

All blog posts · Guides: Photo to pattern guide · Cross stitch app for beginners · PDF charts on iPhone